Showing results: 76 - 90 of 108 items found.
-
448 -
SCI
Our 448 model is a 4-in-1 tester with 500VA AC Hipot, DC Hipot, Insulation Resistance and Ground Bond testing capabilities. The 448 is capable of a 500VA AC Hipot output to comply with 100mA leakage current test compliance requirements. This tester features a simple design and easy-to-use interface, reducing setup time and increasing production-line throughput for your application.
-
JP3X Series -
Danbridge a/s
The Danbridge non-destructive High Voltage Insulation Testers meet the demands for a gentle method of testing insulation condition and detecting leakage currents while protecting hardware, components and materials. Danbridge have two High Voltage Insulation Testers depending on requirements - JP30A can test using up to 30k volt, while JP36A is used when voltages up to 36k volt are desired.
-
MT2 -
Draper Tools Ltd
Multi-functional tester with plain slot blade that allows the checking of wiring without dismantling or having any contact with live parts. Applications include 'break point' in wiring, continuity testing, bulb and fuse testing, microwave leakage, socket testing and testing for static. Fully insulated. Full instructional leaflet supplied. Supplied with 2 x 1.5V alkaline batteries.
-
MFY-CM -
Jinan Saicheng Instrument
Saicheng Vacuum Leak Tester (also called Leak Detector, Leak Test Apparatus) is professionally designed for the leakage tests of packages, bottles & pouches for food, drugs, medical instruments, household chemical products, cars, electronic components, stationeries and other industrial products. The instrument also can be used to test seal performance of specimens after falling and compression tests.
-
Model 4702 -
Barth Electronics, Inc
The Model 4702 HMM+™ is a completely new tester primarily intended for device level testing and produces a current waveform as specified in the IEC-61000-4-2, from a 50 ohm source impedance system.*This tester provides device level test data that allows users to evaluate the IEC current waveform protection level of their devices. We included failure identification by leakage current increases in the 4702 tester so precise pass/failure levels can be closely measured.*The 4702 HMM+™ provides a new and improved test connection method for making quantifiable and repeatable device level HMM measurements.*Convenient, precise, repeatable operation*Computer controlled for automated testing
-
inTEST Corporation
The primary element of the tester electrical interface is the Probe Pin Ring (PPR). Sometimes referred to as a ‘tower,’ this array of spring-loaded probes can be arranged to provide a controlled impedance path, a low leakage connection, a low inductance arrangement for high currents, or just about any connection characteristic you require. inTEST EMS provides electrical interfaces in various OEM-supported designs, inTEST standards, and custom configurations.
-
400SW -
Tokyo Electronics Trading Co., Ltd.
Semi-automated ESD tester featuring Ecdm 400E, Universal ESD Simulator. Used with a manual wafer probing system or a die manipulator, wafer or die level semi-auto ESD test can be done, as well as packaged device test. Damage is detected by V-I curve or leakage current change detection.
-
Greenlee Tools
A cable insulation resistance test is a test that is performed by applying 500 V or more between the conductor and ground and measuring the resulting leakage current. An insulation resistance tester is a test instrument that measures current that leaks through the insulation into ground. Insulation resistance tests can be performed with insulation multi- meters (IMMs) or megohmmeters. Insulation resistance testers are calibrated to display megohms (MΩ) of resistance. A satisfactory insulation resistance measurement should be in millions of ohms.
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's Battery Pack Drop Tester Relevant standards requirement:Test object: battery pack and systemTest procedure: The test object is most likely to fall in the direction of actual maintenance or installation. If it is not possible to determine the most likely fall direction, fall in the Z-axis direction, and the battery pack will fall from the height of 1 m to the concrete floor and observe for 2 hours.Accept standard: The battery pack or system has no electrolyte leakage, fire nor explosion.
-
SFB150 -
Shanghai Launch Electric Co., Ltd.
Zinc oxide arrester tester is specifically designed to detect internal electrical defects of power system with 10KV and below using MOA valve clearance indirect contact and to measure leakage current under MOA DC reference voltage (U1mA) and 0.75 U1mA. The instrument integrates high-voltage DC power supply, measurement and control system. All components are concentrated in a single chassis, with small size, light weight. It is a must for power system and zinc oxide arrester tester manufacturer field test.
-
Extech 382357 -
Extech Instruments Corporation
The 382357 is a Clamp-On Ground Resistance Tester that enables non-contact measurements of ground conductors. True RMS AC Leakage current range of 0.2mA to 30A with 1.000mA resolution. Programmable Datalogging with 116 data points. Performs without the need for auxiliary spikes. Complete with 9V battery, Resistance check plate and durable metal storage case.
-
DRK218 -
Shandong Drick Instruments Co., Ltd.
DRK218 breakdown voltage tester is controlled by the computer, through a new smart digital integrated circuits developed by my company and software control system to make the step-up rate is truly uniform, accurate, and be able to accurately measure the leakage current data. Real-time rendering test curve accurate judgment and it can save, analyze and print test data.
-
CP501 -
Martindale Electric Co. Ltd
The most popular socket tester available - detects 28 fault conditions.
A quick and easy way to ensure that 13A sockets are correctly wired, indicated by 3 bright long life LEDs.
Wiring faults are indicated by one or more of the LEDs failing to illuminate, with the pattern of lit LEDs indicating the type of fault detected. This fail-safe system means that any LED not lit indicates a fault. The robust ABS housing has a sculpted shape for easy removal and there is a look up chart on the tester for quick fault diagnosis.
The plug induces less than 5mA of earth leakage, well below RCD trip thresholds.
-
RK7112 -
Shenzhen Chuangxin Instruments Co., Ltd.
The tester is applied to the home appliances, computer peripheral equipment, electric products, communication products, lighting products, small home appliance products, lighting equipment, electronic components, transformers, motors, compressors, electric heat pipe, wire, cable and high voltage safety system’s withstand voltage and leakage current test, as well as it’s an indispensable dielectric
-
Amida Technology, Inc.
AMIDA 2020XP CIS tester is the latest generation of CMOS image sensor-specific measuring instruments from Metatech. In addition to the original true and accurate measurement, the high-throughput mass production solution designed for the high-throughput inspection of image lens modules and camera lenses has been well received after nearly 20 years of mass production experience. First-class factories at home and abroad import production. AMIDA 2020XP CIS testing machine not only meets the customer's testing time and high output and accuracy requirements. Within the range of functional flexibility, users can customize their measurement requirements according to the definition of various sensors. AMIDA 2020XP CIS tester is a new generation of CMOS Image Sensor dedicated tester, which integrates DC open/short/leakage test, AC Pattern test and image test. It uses 180 Pin high-speed cable to connect to the test end